Jul 30, 2025
1. Installation and calibration optimization
1. Precise centering and leveling
During installation, strictly calibrate the axis alignment of the motor, reducer, and ball mill barrel (or transmission pinion shaft) to ensure that the radial deviation is ≤0.1mm and the axial deviation is ≤0.5mm/m (can be detected by a dial indicator or laser centering instrument);
The reducer base needs to be fixed horizontally (horizontal error ≤0.1mm/m), and the anchor bolts are tightened diagonally in steps according to the specified torque (refer to the equipment manual) to avoid deformation of the shell due to uneven force.
2. Gear meshing accuracy control
Check the meshing contact spots of the large and small gears (along the tooth height ≥40%, along the tooth length ≥50%), and fine-tune the meshing position by adjusting the bearing seat gasket;
Newly replaced gears need to be installed in pairs to ensure that the tooth side clearance meets the standard (usually 0.2-0.5mm, adjusted with the gear modulus).
2. Fine management of lubrication system
1. Selection and replacement of lubricating oil
Select suitable oil according to the equipment manual (such as medium-load industrial gear oil CKC/CKD series, the viscosity is selected according to the ambient temperature, high viscosity in summer and low viscosity in winter);
Change the oil for the first time after the new reducer runs for 100 hours (to remove the initial running-in impurities), and then change the oil every 3-6 months (or replace it in advance according to the oil quality test results);
Clean the oil tank, filter and gearbox thoroughly when changing the oil to avoid mixing new and old oils or impurities remaining.
2. Daily maintenance of lubrication system
Check the oil level daily (keep it at 1/2-2/3 height through the oil level gauge), and replenish it in time when it is insufficient (same type of oil);
Check the lubrication pump pressure every week (to ensure that the oil nozzle effectively supplies oil to the gear meshing area), and clean the oil circuit blockage (such as oil pipes and filters);
The bearing cavity needs to be filled with special grease (such as lithium-based grease) on a periodic basis to avoid mixing different types of greases and causing failure.
3. Load and operation status monitoring
1. Avoid overload and impact
Control the feed amount evenly (adjusted by the feeder) to prevent the cylinder from "stuck" and causing the reducer to overload instantly;
Clean metal foreign matter (such as bolts, iron blocks) in the cylinder regularly to prevent the grinding body from impacting and damaging the gears;
Install overload protection devices (such as motor current protectors, torque limiters), and automatically shut down when the limit is exceeded.
2. Real-time monitoring of key parameters
Record the reducer housing temperature (normal ≤60℃, if it exceeds 70℃, it needs to be shut down for inspection) and vibration value (effective value of speed ≤6.3mm/s) during daily inspections;
Take samples of lubricating oil regularly (monthly) to judge the gear/bearing wear trend by the metal particle content (iron, copper elements) in the oil;
Monitor the running sound. If there is any abnormal sound (such as metal friction sound, periodic knocking sound), stop the machine immediately for investigation.
4. Maintenance of fasteners and seals
1. Bolt anti-loosening and tightening
Check the tightening status of the anchor bolts, bearing seat bolts, and end cover bolts every week, and re-tighten them according to the specified torque (using the diagonal step method);
Install anti-loosening devices (such as stop washers, double nuts, thread glue) on the parts that are easy to loosen to prevent the bolts from loosening due to vibration;
If the bolt hole is threaded, repair it in time (expand the hole and tap it to replace the thickened bolts or weld the nuts) to prevent the housing joint surface from being misaligned.
2. Regular replacement of seals
Check the sealing of the input/output shaft oil seal and the housing joint surface gasket every 6 months, and replace them in time if oil leakage is found (use oil-resistant and temperature-resistant fluororubber materials);
When replacing seals, clean the oil stains and burrs on the joint surface, and evenly apply sealant (such as Loctite 510 flat sealant) to enhance the sealing.
5. Long-term operation and maintenance strategy
1. Regular disassembly inspection
The reducer should be disassembled and overhauled every 1-2 years (or 10,000 hours of operation), with key inspections:
Gear tooth surface wear, pitting, and bonding (wear exceeding 15% of the tooth thickness requires replacement);
Bearing clearance (exceeding 2 times the standard value requires replacement), raceway and roller surface conditions;
Wear degree of journal and keyway to ensure matching accuracy.
2. Environmental protection
Keep the area around the reducer clean to prevent dust and water vapor from entering (protective cover can be installed);
Strengthen heat dissipation in high temperature environment (clean heat sink, install axial flow fan), and regularly check the rust of the shell in humid environment and apply paint for protection.
